Beemaster's International Beekeeping Forum

BEEKEEPING LEARNING CENTER => EQUIPMENT USAGE, EXPERIMENTATION, HIVE PLANS, CONSTRUCTION TIPS AND TOOLS => Topic started by: Summerbee on December 31, 2005, 01:13:59 pm

Title: homemade extractor
Post by: Summerbee on December 31, 2005, 01:13:59 pm: Hello,
Does anyone have any plans for making extractors from scratch? I hate to buy one at the exorbinant prices of the catalogs. I was thinking taking a 10 gallon bucket and wiring a basket in for maybe one or 2 frames, and modifying the lide with a crank, and having an axel go from lide to bottom. Then drilling a hole near the bottom and creating a spout mechanism out of something.
If nobody has any ideas I'll tell you how my frankenstein extractor turns out.
Thanx.
Title: homemade extractor
Post by: Finsky on December 31, 2005, 02:02:54 pm: I made my first exctractor but I do not recommend. The first is that odor of honey leaks and spinning of frames ventilates taste of honey away. Little exctractor is very cheap. Not good job to do your own.

Here cheapest is 400$
Title: homemade extractor
Post by: thegolfpsycho on December 31, 2005, 02:11:18 pm: There are plans for building your own extractor on beesource. There is also an extractor called something like the "Little Wonder" It's only about $138 if I remember right. A 2 frame tangental model, plastic drum, plastic gears, honey gate, etc.

There was also a fellow on beesource that challenged and built an extractor for about $50. Looked kinda hazardous to me, but it worked.

M Bush is a big fan of crush and strain until you get your hive count up. Something to consider.
Title: homemade extractor
Post by: Jay on December 31, 2005, 04:40:32 pm: Here are some things to look at if you would like to build your own extractor. If you decide to make one out of wood, I would recomend that you coat all surfaces that will contact the honey with food grade epoxy paint. Good luck! :D

http://www.beesource.com/plans/extractor_4.htm
http://www.beesource.com/plans/extractor_20.htm
http://cgi.ebay.com/Build-Your-Own-Honey-Extractor-1983_W0QQitemZ4597928954QQcategoryZ378QQssPageNameZWD1VQQrdZ1QQcmdZViewItem
http://cgi.ebay.com/Homemade-HONEY-EXTRACTOR-doesnt-damage-comb-DIY-PLANS_W0QQitemZ7559525574QQcategoryZ46527QQssPageNameZWD1VQQrdZ1QQcmdZViewItem
http://cgi.ebay.com/Rotary-HONEY-EXTRACTOR-Doesnt-Damage-Honeycomb-Plans_W0QQitemZ7563764209QQcategoryZ46527QQssPageNameZWD1VQQrdZ1QQcmdZViewItem
Title: homemade extractor
Post by: Horns Pure Honey on December 31, 2005, 04:45:10 pm: I would say buy one, in the end it will pay for itself, believe me, bye :D
Title: homemade extractor
Post by: Michael Bush on December 31, 2005, 05:44:32 pm: I did finally buy one about six years ago, but for 25 years I had bees without an extractor. Crush and strain works fine. I didn't buy one until I could afford a REAL one. I got a 9/18 radial and have never regretted holding out for a serious one. It still takes too much time. But crush and strain is faster than a two frame non-reversable. :)
Title: homemade extractor
Post by: Hi-Tech on April 30, 2006, 02:19:53 am: What is the "crush & Strain" method?
Title: homemade extractor
Post by: manowar422 on April 30, 2006, 10:07:11 am: Don't over look the possibility of used equipment.

Last year I picked up a hand cranked 9 frame radial
stainless extractor, plastic uncapping tank, scratcher
and knife for $350 off eBay 8)
Title: homemade extractor
Post by: Michael Bush on April 30, 2006, 01:43:58 pm: >What is the "crush & Strain" method?

http://www.bushfarms.com/beesharvest.htm
Title: homemade extractor
Post by: Hi-Tech on April 30, 2006, 06:50:41 pm: MB,

One of these days I am just going to read your entire website,from front to back, so I will stop asking questions you have already addressed....

Thanks
Title: homemade extractor
Post by: KONASDAD on May 11, 2006, 01:24:47 pm: I realize this is an old thread, but i have a question. When doing crush & strain, does it matter what kind of foundation is used? Does it have to be 100% beeswax, or can duraglit or plasticell be used? thanx in advance.
Title: homemade extractor
Post by: Brian D. Bray on May 12, 2006, 12:08:59 pm: If cost is a major consideration Dadant has a plastic 2 frame tangent for $105.95, new, on page 76 of their current catalog the PLU (aka UPI or IPU) is MOO389. The shipping weight is listed as 30 lbs but over size restrictions may apply--the catalog doesn't indicate if so. Contact Terry Avise (tavize@dadant.com) and ask about shipping. I haven't seen the plastic extractor advertised in their online catalog website.
They also have a stainless 2 frame tangent for as little as $245.69 on the same page.
You can buy it cheaper than you can make it.
Title: homemade extractor
Post by: Apis629 on May 12, 2006, 12:21:57 pm: I bought that stainless steel 2 frame non-revesable exctractor and, while it works well, I wish it had one of the reversing baskets just to speed things up. When I bought it, however, it was $233.95.
Title: homemade extractor
Post by: Ross on May 13, 2006, 08:27:38 pm: I was told to wait until I really needed one (Michael Bush) or pick up a used one (everybody). I went 4 years looking for a used one. Found a 9 frame last year, but it was frozen up. This year a nice stainless, powered 20 frame showed up about an hour away for a great price. They do show up, but it can take awhile. If you have enough honey to call it a business, buy a good one. If not, wait, make cut comb, or break and strain as Michael has said.