Not sure where this will go, as I am just looking for a bit of discussion on something I have found several times, but will use one instance as the basis...
Not long after I began beekeeping, my mother called me in hysterics.. still laughing in fits...
My father was cleaning the hill out at the farm, lugging all the stuff he could pick up to the trailer to haul it to the salvage yard.. apparently, she watched him grab an old well/water pressure tank, and head toward the trailer with it... he quickly dropped it.. jumped up in the air flailing wildly... then he started waving his cap about and took off at high speed across the yard.. dad is in his 60's, and doesnt often run.. but apparently he was making good time across the yard...
Moms first reaction when she realized that he was getting attacked by bees was to shut, and lock the door... thinking better of that, she ran for the bedroom and shut and locked that door, as dad came through the front door in excess of 80 MPH...
Anyhow.. upon investigation, he was moving a tank I had known about for MANY years to have bees in it, but had LONG since forgotten about... I had found that tank many years ago looking for misc pieces of steel to build some project with..
I picked it up gently, re oriented it so the right side was up, and placed it back where it had been.. I did not get stung...
I waited until that evening when all the bees were back, screened over two entrances, and taped the other two shut. put it in my truck and brought it home..
It was my first cutout.. the tank was about three feet long and about eighteen inches in diameter, made of galvanized steel. it had four inch holes in different locations. the tank had been left with the holes pointing between the nine and ten oclock position, with One hole straight up..
When I cut the tank open.. I found it packed FULL of old brown and black comb. I carefully cut each piece of comb away, shook the bees into a deep body with a couple frames pulled out.. about 3/4 through cutting all the comb out, the bees started orienting on the hive, instead of the can, so i assume thats when the queen was shaken into the hive body.. I did the classic rubber band trick to attach their comb to four empty frames, and set those into the hive.. I still have this hive, and it is one of the gentlest and best producing hives I have. The bees are yellower, with yellow alternating with the black on their abdomens all the way to the tip.. most other bees I have, carniolans and itallians are not this yellow, or this small, and not as gentle.. They are more orange with black and white abdomens.
Anyhow.. i often see discussions on Ventilation and swarm hive location, and this metal container could NOT have had good insulation or ventilation. It's location was also ON the ground, with the openings positioned so that rain most certainly got into them, if not in large amounts.
The bottom of the canister had about an inch and a half of rust and debris in it, the rest of this hive was attached directly to the metal sides. This hive was also in full shade 100% of the time. Trees, brush, and a plenitude of metal debris from tractors and farm implements covering it.. Seeing discussions on hive ventilation and insulation makes me wonder how this hive ever survived.. much less survived for the thirteen years I am certain of... Yes, it is possible it was constantly re filled by swarms from the hive in the big tree in the front.. but I also saw old queen cells, and new queen cells on some of the unused portions of the comb, so am relatively certain that this hive had overwintered many times...
Jut trying to understand how bees can do everything wrong according to all I have read, and still survive...
As a side mention.. I have taken hives from old cars, old farm equipment, an old steel tool box from a truck that had been in use for at least four years. A combine tire, still on the rim that had a two inch gash in the side of it, was propped up against the side of a tree, and allowed to sit there for many years. And the most interesting one.. a LARGE hive in an old grinder mixer tank.. I liked that one.. the mixer had windows in the side of the tank so you could look in and see the bees working away.. I took the window out, and used a vac to get most of the bees.. Opened the top hatch and vacced the comb on that, and used a sawsall to cut open the side.. we took over 30 gallons of honey from that hive....
Temps here in mid winter are usually around 0 - 20 F, with a two or three week period of -20. In summer, 80 -90, with two or three weeks of near or just over 100.
SO...
One, how can they survive in metal? Cold doesnt kill bees.. cold and WET kills bees? What about heat in full sun in metal?
Two, Ventilation.. VERY little in some of the hives I cut out, especially the combine tire.. ONE hole, black tire.. I wonder why the comb didnt melt when the temps were over 100 and the sun was shining on it...
Three, what was the most interesting thing you found bees in?